Page 22 - Exitflex
P. 22
Tungsten carbide inserts Product specification sheet Spray tip programme 0.006 0.15 2/3 in. 4/6 in. 6/8 in. 8/10 in. 10/12 in. 12/14 in. 14/16 in. 16/1 in. 18/20 in. 20/22 in. 22/24 in. L/min G/min
Flow rate (water at
Spray angles in degrees and pattern width in inches at 30 cm
Equivalent
100 Bar / 1500 psi)
Orifice Size
90°
80°
110°
100°
70°
30°
20°
10°
60°
50°
40°
Inch mm
Bulk supply, C (USA), D and Speedy
0.040
0.14
C (USA)
0.007 0.18
0.047
0.18
D (Airmix)
0.22
0.060
0.008 0.20
Speedy
0.009 0.23
0.090
0.010 0.25
0.33
0.011 0.28 0.25 0.066
0.10
0.37
0.012 0.30 0.47 0.13
0.013 0.33 0.57 0.15
Ordering example
0.014 0.35 0.65 0.18
A customer requests a bulk-
0.015 0.38 0.72 0.19
supply of Speedy inserts with a
0.016 0.40 0.91 0.24
flow rate of 0.25 L/min at 100
0.017 0.43 0.98 0.26
Bar and a spray pattern of 8 to
10 inches at 30 cm. The spray 0.018 0.45 1.10 0.29
tip programme table gives us 0.019 0.48 1.30 0.34
0.020 0.50 1.40 0.37
1- an angle of 40°(coded 40)
0.021 0.53 1.52 0.40
2 - and an equivalent orifice size
0.022 0.55 1.65 0.45
of 0.009 inch (coded 9)
0.023 0.58 1.83 0.48
3 - The complete part reference 0.024 0.60 1.95 0.54
number is therefore
0.025 0.63 2.13 0.56
88-030 409
0.027 0.68 2.50 0.66
0.029 0.73 2.95 0.78
0.031 0.78 3.42 0.90
0.033 0.84 3.80 1.00
Conversion factors
0.035 0.89 4.30 1.14
Volume 0.037 0.94 5.10 1.34
From To Multiply by
Liters Gallons 0.2642 0.039 0.99 5.50 1.45
Gallons Liters 3.785
0.041 1.04 6.15 1.62
Flow 0.043 1.09 6.80 1.79
From To Multiply by
Liter/min Gallons/min. 0.2642 0.045 1.14 7.40 1.95
Gallons/min. Liters/min. 3.785
0.047 1.19 7.94 2.09
Length 0.049 1.24 8.50 2.25
From To Multiply by
Inches Centimeters 2.54 0.051 1.29 9.10 2.40
Millimeters 25.4
Millimeters Inches 0.0394 0.053 1.35 9.80 2.60
Centimeters Inches 0.3937 0.055 1.40 11.00 2.90
0.057 1.45 11.80 3.10
0.059 1.50 12.50 3.30
0.061 1.55 13.70 3.60
10° 20° 30° 40° 50° 60° 70° 80° 90° 100° 110°
   17   18   19   20   21   22   23   24